Product Description

Also name

Pure resistance lightning pulse divider, high voltage pulse impulse divider, pulse voltage divider, pure resistance pulse voltage divider, the standard pure resistor divider, lightning pulse voltage divider, the standard impact voltage divider, high voltage pulse Voltage divider, standard pure resistance lightning high voltage pulse impulse voltage divider

Functional overview

This equipment is equipped with high voltage pulse voltage divider, collecting high frequency and power frequency voltage signal, mainly used for lightning wave measurement, power system overvoltage (operating over voltage, ferromagnetic resonance overvoltage, series resonant overvoltage, etc.) and the system Frequency voltage.

The high voltage pulse divider will serve as a front-end component of the overvoltage on-line monitoring system, providing the relevant attenuator and connected to the overvoltage on-line monitoring system via a dedicated shielded cable for system overvoltage monitoring.

1. a high voltage side

A) a high voltage side of the installation: from the high voltage power grid bus access to the high voltage side of the high voltage arrester and with the high side of the high voltage side of the voltage divider to complete a high voltage side of the installation. The voltage divider is single phase, divided into A, B, C phase, single phase direct connection.

B) can collect high frequency and frequency of the voltage signal.

2. Secondary, measurement monitoring side:

A) secondary monitoring side wiring: the supplier is equipped with a good voltage divider measurement output interface connector, the supplier should be equipped with attenuator interface connector, the middle is connected to the demand side of the measurement cable signal The attenuator of the line and the supplier forms the measurement loop. Intermediate connection of the measurement cable signal line must be armored flame retardant tape with the measurement cable signal line: coaxial *****1 or *****2 RF shielding cable. Anti-interference ability of the best. Secondary regulator side of the voltage divider Output port connector: Yes SL*6 connector. Coaxial.

B) The voltage output of the secondary side of the voltage divider is **0V, and the voltage to the data acquisition mechanism is *0V. The buffer (attenuator) needs to be installed.

C) Secondary output range: depending on the ratio of the partial pressure ratio. Ratio of large voltage is low, the ratio of small voltage high.

3. lightning high voltage pulse divider works:

Coupled pulse current signal.

Main technical data

1. High voltage pulse divider parameters

Rated voltage: **0kV (0 ~ **0kV) a high voltage side

Rated capacitance: ***0pF

Capacitance section: 1 section

Resistance and inductance: 0 ~ *0Ω, 0 ~ *0uH

Each section capacitance: ***0pF (MWF**0kV ~ ***0pF pulse capacitor)

Square wave response: part of the response time is less than **0ns, overshoot less than *0%

Partition ratio: **0: 1

Secondary side of the measurement port Output voltage: **0V (0 ~ **0V)

Partition ratio Uncertainty (measurement accuracy): less than 1%

Installation type: indoor or cabinet installation requirements, synthetic silicone rubber casing insulation shell.

Long-term operation in the *0kV power grid to run, to meet the following waveform monitoring:

A. Standard lightning impulse full-wave voltage waveform

Wave head time: 1.2 ±*0%μs

Tail time: *0 ±*0%μs

Overshoot: less than 5%

Efficiency: no less than *0%

± 1.2 / *0μs standard lightning impulse full-wave, the efficiency is greater than *0%.

B. Standard lightning impulse voltage waveform

Wave head time: 1.2 ±*0%μs

Overshoot: less than 5%

Truncation time: 2 ~ 6μs, electronic delay control

Efficiency: no less than *0%

Using the truncation device can produce truncation time 2 ~ 6μs lightning truncation, truncation dispersion is less than **0ns.

C. Standard operation shock full wave voltage waveform

Wave time: **0 ±*0%μs

Tail time: ***0 ±*0%μs

Efficiency: not less than *0%

± **0 / ***0μs standard operating shock voltage wave, the efficiency is greater than *0%.

D. produces steep wave shock waveforms with steepness greater than ***0 kV / μs

2. attenuator (buffer) parameter

**0V / *0V ( / output)

Partition ratio: *0: 1

Attenuator for the voltage divider *0k ohm, to prevent the voltage is too high, can access the monitoring equipment to protect

Attenuator and output port of the connector: are Q9 connector. Coaxial.

Coaxial connection connector and coaxial shield measurement cable frequency AC voltage and lightning impulse withstand voltage insulation level: ≤4kV.

Equipment size

Dimensions: **0Hx**0Wx**0L (mm), single weight: *5kg.

Installation size: **0Hx**0Wx**0L (mm