Product Description
The fearture are as below:
1. Advanced design
The HK Series Electric actuators offers many specially
performances, high cost-effective even its applies in the general
situation.
Non-intrusiveswitching:
The HK Series Electric actuators utilizes
magnetic induction mode switching without any shafts
penetrating the shell.
Non-intrusivesetting:
The actuators operational parameter setting are effected using
the non-intrusively, hand held, infra-red setting tool.
Double sealed:
All the HK series actuators are housed in a double-sealed
enclosure and provide complete protection to the internal equipment
even if the terminal cover are removed during site wiring, the type
of waterproof actuator can running *8 hours while the actuator
immerge into water deep 3 meters.
Torque protection:
A sensor serve as overload protection for the entire valve
travel, and you can setup a different torque volume between *0~**0%
of rated torque, in addition the open torque protection value can
be different from close torque.
Limitprotectionsetting:
If this function is enable, the actuator shall be stopped
automatically while the valve position reaches the limit
position.
Loss Phase protection:
The actuators real time monitor all three phase of the power
supply during operation to prevent the motor from running when
the power supply is short of phase.
Electronic Latching :
Electronic Latching inhibits the actuator torque protection
function within 5 seconds and allows the motor to generate torque
in excess of rated torque to enable operation of jammed valves
while starting operation signal is enable , should the actuator
stall when attempting to unseat a valve stuck in its seat, the
motor will be de-energised to prevent damage.
Motor thermal protection:
Two thermostats are embedded in the windings for provide
thermal-protection by de-energise motor in the event of motor over
the maximum temperature.
Electric protection:
The and output signal channel of circuits are designed
as photoelectric isolate mode.
Valve position and torque measure:
Use hall effect magnetic pulse system continually monitoring
the valve position and use the magnetic flux and current of the
motor for continually measures the controlling torque are to avoid
the mechanical wearing and ensure function stability.
Automatic correction for phase
sequence:
The actuators monitor the phases and run in the correct
direction regardless of the sequence of power supply connection
that is realized through a phase rotation correction Boolean
logical calculation .
Setting the following configurations with infra-red setting
tool
² Direction
to close
² Close
limit position protection function
² Close/
open operation torque value
² Open
/close limit position
² ESD
Optional function (ESD: Emergency shut down)
Digital indication of valve position:
The percentage digital of valve position real time indicates
on LCD display.
Power failed protection:
If main power failed, the internal battery of the actuator
should supply power for control circuit and supports valve position
control in hand operation. In case of no battery available,
actuator can save the currently valve position Data as well.
Handwheel operation:
Direct drive handwheel to provide reliable emergency manual
operation in the event of a power supply failure. Electric
operation always has the higher priority than manual operation,
when motor is energized that the operation state automatic switch
to electric operation mode unless hand/auto lever is purposely
locked into ‘manual operation’
Explosion proof:
The actuators has high class enclosure which is designed
according to GB***6, it provides reliable ingress and seals
guarantee. In addition, the threaded is designed at the cable entry
conduit of the actuator for fixing explosion proof
tube.
High torque, low inertia motor:
The low inertia and high torque motor generates peak torque
rapidly after starting but with very little overrun when it is
de-energized.
Lubrication:
HK series are filled with high-quality gear oil, the most
important machine parts such as worm and turbine operates in an oil
bath to reduce wearing and extend life.
Standard valve/actuator interface:
Actuator Base of ranges HK*3 to HK*0, designed as a removable
mode and Series HK**0 to HK**0 as an integral mode, the flange and
drive bushing conforming to international standard ISO***0
Thrust bearing configuration:
The type ‘A’ is the thrust type drive bushing that couples a
fully sealed and lubricated thrust bearing to guarantee which have
not any load effects on the actuator inner structure.
Solid state circuit measure:
All of Series HK provides the solid state circuit to measure
the torque without any mechanical equipments such as the spring
switch or the level.
Hurko valve actuator have Basic,Modbus-Rtu,Profibus,FF and ect
type.
For more detailed information ,please contact us.
Thanks!
Max Wen
Hurko Science & Technology Co.,Ltd.China
| Country: |
China |
| Model No: |
HK Series
|
| FOB Price: |
(Negotiable)
Get Latest Price
|
| Place of Origin: |
CHINA |
| Price for Minimum Order: |
- |
| Minimum Order Quantity: |
1 Set |
| Packaging Detail: |
Wooden case |
| Delivery Time: |
20days depend on quantity |
| Supplying Ability: |
2000 Piece per Month |
| Payment Type: |
L/C, T/T |
| Product Group : |
Multi-Turn Valve Actuators
|
