FOB Price
Get Latest Price|
1 Piece Minimum Order
Country:
China
Model No:
Shaping machine
FOB Price:
Place of Origin:
-
Price for Minimum Order:
-
Minimum Order Quantity:
1 Piece
Packaging Detail:
-
Delivery Time:
-
Supplying Ability:
-
Payment Type:
-
Product Group :
Contact Person nadosales002-cn.nadosales002.061414
BaiZiwan, Beijing
Molding machines, also known as out of the box machine is
automatically out of the box, forming, bending under the bottom
hinge. And now to complete the next part of the taped, will mount
into open cardboard box board, according to certain procedures
equivalent to the bottom of the box, and sealed with tape transport
to the packing machine of special equipment. Automatic carton
forming machine, automatic high-volume carton box machine is
automatically out of the box, under the cover automatically
converted, self-sealing tape under the bottom of the line
equipment, machines used in all PLC + display control, greatly
facilitate the operation, the scale of production will be automated
essential equipment.
Machine characteristics
molding machine adopts imported PLC mainframe computer chips,
matching LCD display, backup software malfunction self-diagnostic
system and error correction features that make operation more
convenient, the design control procedures in order to fool without
professional training to operate induction .
molding machine hydraulic drive, hydraulic stepless has pioneered FM technology to solve a variety of materials, machine and block-type fitness, increase the density of the material, shortening the molding cycle.
to use Machine
1, choose the flat table, put stable machine, pull the foot box can
be easy to observe the machine panel.
2, the hand-held sensor head plugs into the socket on the panel and
tighten. Note positioning gap
3, one end of the power cord socket on the rear panel into the
chassis, the other end into a power supply outlet, be sure to use
the single-phase three-wire power supply.
4, open the case after the board of the "power switch (POWER SW.)",
According to panel "power switch (SWITCHING)" , to be "ready
(WARM UP)" green light, the machine can work.
5, hold down the "set (SETTING BUTTON)" , set to
appropriate values, generally between 0.**2.0 seconds.
6, the sensor head on the container lid above, click the start
on the handle, then the "heating (HEATING)" red light, that
is heating, do not remove the sensor head, "heating (HEATING)" red
light off and then remove the sensor head, and other "ready (WARM
UP)" green light or buzzer inside the short sound "beep" prompt and
then the container can be sealed next job.
7, check the seal of quality, depending on the material, the
diameter of the container and the production efficiency, proper
trimming "setting (SETTING BUTTON) key to make the best
sealing quality.
Machine works
Machine works with an injection with a syringe similar, it is with
the screw (or plunger) of thrust, will have a good molten plastics
(ie, viscous flow) closed well into the plastic injection mold
cavity, the products obtained after curing shaping process.
Injection molding is a cyclic process, with each cycle including:
dosing - molten plastics - pressure injection - filling the cooling
- Kai-mode pickup. Remove the plastic parts and then re-closed
mode, the next cycle.
Machine technical parameters
Lack of tape and cardboard boxes automatically when the alarm
Power: |
Single-phase **0V、*0Hz/*0Hz、**0w |
Atmospheric pressure: |
6kg/cm2 |
Tape width: |
4.**6.0cm |
Forming speed: |
*2 Boxes / minute |
Carton: |
Maximum size:L**0mm,W**0mm,H**0mm |
Minimum size: |
L**0mm,W**0mm,H**0mm |
Weight: |
About **0kg |
Country: | China |
Model No: | Shaping machine |
FOB Price: | Get Latest Price |
Place of Origin: | - |
Price for Minimum Order: | - |
Minimum Order Quantity: | 1 Piece |
Packaging Detail: | - |
Delivery Time: | - |
Supplying Ability: | - |
Payment Type: | - |
Product Group : | Pressure the ball |