The Main Technical Parameters of The Pipe Bending
machine
|
Model |
**4mm×*0mm |
Date |
9th Jan |
Term of
validity |
*0
days |
Duration |
*0
Work Days |
|
Size L*W*H
m |
*8*1.8*1.8 |
Weight |
About *6T |
Working
scope |
******4**0mm carbon steel pipe with
Max length *2mm，Bending
radius3 D to 8 D |
Cost
(FOB) |
USD |
EXW： USD (travel charges for the 2
or three technicians to install the machine should be
paidadditionally) |
|
Tianjin |
The
MainTechnicalParameters of The Pipe Bending
Machine
1、Master cylinder：OD:**9mm, inside
diameter:φ**0mm diameter of the
rod:φ**0mm
effective stroke: *1 m the max
thrust of the 2 cylinders **0T
The
other small cylinders:φ**5mm *2 pieces（for clamping）
2、Hydraulic pump
station
a、station configuration:
*5scy plunger pump 1 set、7.5KWMotor
1 set ( to converse frequency
adjust
the speed of the master pump)
CB***0 gear pump 1
set、*5KW Motor 1 set ( fast
forward and backward，).
*0scy plunger pump 1 set,*1kw motor
1 set (to guide clamp wheel、fixture
motor)
The working speed ;
***0cm/min,
themaximum
returning speed:**0cm/min
3、The guiding part of the main machine
is controlled by four wheels, the pushing board moving on the
dovetail groove guiding rails. the clamp holding different size
runBy the hydraulic motor, it open and
closed driven by the oil cylinder, the oil cylinder drive the
rocking arm to adjust the bending radius.
4、Medium—frequency
power supply (SCR)：
power:**0kw. Quenching transformer:
***0kva.
5、the total powerof
the machinery:
*5KW，**0V or **0V,*0or*0HZ.
6、Assembly
parts
a、clamp wheel、fixture made of *5# cast
steel
b、master fuselage、weldment、the main pushing board are welded
board
c、screw、chain、standard parts and bearing are
national standards
d、the guider is dovetail groove slide
plate mode |
The
works and the scope of supply of the
supplier
1.
Design and manufacture pipe bending
machine
2.Guide to install the equipment as the
equipment arrives at the factory of buyer
3.Debugging and test run the equipment
(three technicians to the buyers factory)
4.Main machine part, hydraulic pump
station, heating system.
5.Φ**4,Φ**2mm,**0mm,**8mm,**7mm,**6mm,**4mm,**9mm
clamping device: 1 piece for each size.
Φ**4Φ**2mm,**0mm,**8mm,**7mm,**6mm,**4mm,**9mm
induction heating coils: 1 piece for each
size.
6.The equipment foundation drawing,
hydraulic principle drawing, electrical diagram, each with 1
copy
7
spareparts for the machine and the heating
device |
The
purchasershould prepare
1. the
power source and the wire to the equipment electrical
ark
2.
cement foundation, steel ground, ground
screw
4. the
other type of clamping, reforming equipment, hydraulic
oil
5.
provide the hoisting and the necessary installation tools of the
equipment and the raw material of test
running |
After-sales
service
We are
responsible for the repair in one year after the machine out of our
factory, (except the human factors); |
Payment
terms |
30% advance payment by T/T
beforethe production,TT
*0%
by T/T before goods
delivery.TT |
|
