Protocol converter series(interface converter) By Guangzhou Hansun Communication Equipment Co., Ltd,

Product Specification

Product Description

Order Information:

HS-CON**1 FE1/V.*5 converter

Overview:
HS-CON**1 E1 to V.*5 protocol converter can realize the bi-directional data transfer from E1 port to V.*5. This equipment is widely used in communication network including WAN and LAN, realizing the transfer from E1 channel of SDH or PDH equipment to V.*5 which maybe provided with router.

Features:

E1 channel: both framed & unframed are OK, both *5 & **0ohm are OK
Standard: G.**3, line code: HDB3
Alarm system for E1 loss
Support local/remote loop test
DB*5 connector for V.*5, in DCE mode
Multiple clock selection: internal clock, V.*5 line clock and E1 resumptive clock
Panel instruction for easy understanding of equipment working status
Internal power supply, **0V AC and **8V DC optional
Standalone and module for your selection

Specifications:

E1 port
Bit rate: 2.**8Mbit/s***0ppm
Line code: HDB3
Standard: Compatible with ITU-T G**3
Connector: BNC connector with line impedance *5ohm, RJ*5 connector with line impedance **0ohm
Jitter performance: in full compatible with G**2 and G**3
V.*5 port
Line code: NRZ
Bit rate: 2.**8 Mbit/s***0ppm
Connector: DB*5female, with DB*5/M*4 transfer line
Way of Connection: DCE
Clock: Line Clock, Local clock
General
Operating temperature: 0℃**0℃
Power Supply: **8VDC or **0VAC***0%
Dimension: **0mm(L)***3mm(W)**0mm(H)

HS-CON**2 E1/*0BaseT converter

Overview:
The device HS-CON**2 Network Bridge is a high performance, remote, self-learning Ethernet bridge. Its compact size and low cost make it ideal for cost-sensitive bridging applications, or as a LAN extender over bit stream type infrastructures. Its E1 data interface also provides an economical digital access solution for E1 and fractional E1 network Services, which can work at data rates of *4Kbps to ***8Kbps.User data is placed into the E1 frame, using only the required number of timeslots.

Timeslot assignment is accomplished according to the Data Port speed and manual setting of DIP switches. The main E1 link may be clocked from the recovered resumptive clock or from an internal oscillator.For easy to check the fault of network line, the device provides loop selection, both local loop and remote loop.

Features:

High performance bridge for *0Base-T Ethernet extension
Fully compatible with IEEE **2.3 and Ethernet Standards
E1 channel: both framed & unframed are OK, both *5 & **0ohm are OK
Ethernet Port: *0Mbps, Full/Half Duplex Mode compatible
Ethernet ports support MDI/MDI-X selectionable
Allow transmitting and receiving VLAN data packet
****0 frames per second filtering and forwarding rate
***0 MAC address LAN table, and automatic LAN table learning and aging.
Standalone and Module optional
Power of Chassis: 2 Slots for slide in power supplier module,
AC or DC power supplier module, Redundant Power supported
AC**0V***0%or DC**8V power

Specifications:

LAN port
Standard: Conforms to IEEE**2.3 / *0Base-T Ethernet
Data rate: *0Mbps(*0Mbps/*0Base-T in Full duplex topology)
Compatible on Full/Half duplex topology
Connectors: RJ**5 Connector
Transfer distance: <**0m
E1 port
Standard: ITU G.**3, G.**4,
Jitter Performance: According to ITU G.**3
Bit rate: N**4Kbps, N=1~*1 (Fractional Mode) or 2.**8Mbps(Full Mode)
Line Code: HDB3
Line Impedance: *5/**0ohms optional
Pulse Amplitude: Nominal 2.*7V***0%

General:

Voltage: AC **0V***0%or DC **8V
Power Consumption: <3 Watts
Temperature: 0℃**0℃
Humidity: ***0%(non-condensing)
Size:(Width: from left to right)
Standalone:**2mm(Width)***9mm(Deep)**1mm(High)
Chassis:**8mm(L)***2mm*(W)***8mm(H)

4E1/*0BaseT converter

Overview:
HS-CON**4 4E1/*0BaseT protocol converter is the most newly promoted product that can convert **4E1 to *0Base-T Ethernet, and vice versa. This protocol converter could support **4E1 to Ethernet, which extend the bandwidth to 7.*8Mbps. It is widely used in two LAN connecting, remotemonitor and video broadcasting.

Features:

Fully compatible with IEEE**2.3, ITU-T G**3, G**4 and G**3
Support *0Base-T, **0Base-TX protocol
Support VLAN & IEEE**2.1q packetsEnable any group of CH*-CH4 E1 channel to transmit the data optionally.
Extend the bandwidth to 7.*8Mbps when using 4E1 channels
Support auto-inspection of effective E1 channel without interruption of data transfer.
Automatically cut off the E1Channel when it has LOS and AIS alarm, and inform the remote end simultaneously
Support remote E1 Loop function
*5/**0 ohm Optional of E1 channel impedance
Internal power supply, overall power consumption<3w, AC**0V***0V or DC **8V optional

Specifications:

E1 Port
Bit rate: 2.**8Mb
Line code: HDB3
Standard: in accordance with ITU-T G.**3, G.**4
Connector: BNC connector, line impedance *5ohm
Number of E1: 4
Jitter Performance: compatible with G.**2 and G.*2
Ethernet Port
Data Rate: *0/**0Mbps
Standard: Compatible with IEEE**2.3
Connector: RJ*5
Number of Ports:1 port
Auto-adaption with half/full duplex
Dimension:**0mm(L)***0mm(W)**4mm(H)

8E1/**0Base-T Converter

Country:	China
Model No:	HS-CON202
FOB Price:	40 / (Negotiable) Get Latest Price
Place of Origin:	Guangzhou
Price for Minimum Order:	40
Minimum Order Quantity:	10pairs
Packaging Detail:	-
Delivery Time:	-
Supplying Ability:	980000pcs
Payment Type:	-
Product Group :	-